Search found 12 matches
- Tue Sep 26, 2017 8:05 pm
- Forum: Equipment and Tools (e.g., ski press, core profiler, etc)
- Topic: Ski Tuners
- Replies: 0
- Views: 4277
- Sat Mar 18, 2017 11:37 am
- Forum: Commercial postings
- Topic: Grindrite Ski Tuner and Edger
- Replies: 0
- Views: 7107
Grindrite Ski Tuner and Edger
Used ST1800 (wide belt and stone) w/ ST500 edger Both units are in good-very good condition & well loved. They haven't been in service for 2 years now and were last running well. New relay for texturing controller has been purchased, but not yet installed. LOTS of extra belts! ST1800: - Stone is...
- Mon Jul 13, 2015 10:05 am
- Forum: Yard Sale (non commercial)
- Topic: REDUCED Ski Tuners - Grindrite ST1800 and ST500 For Sale
- Replies: 2
- Views: 6190
Re: Ski Tuners - Grindrite ST1800 and ST500 For Sale
Still available... accepting offers... Used ST1800 (wide belt and stone) w/ ST500 edger Both units are in good-very good condition & well loved. They haven't been in service for 2 years now and were last running well. New relay for texturing controller has been purchased, but not yet installed. ...
- Sun Jan 11, 2015 3:10 pm
- Forum: Yard Sale (non commercial)
- Topic: REDUCED Ski Tuners - Grindrite ST1800 and ST500 For Sale
- Replies: 2
- Views: 6190
REDUCED Ski Tuners - Grindrite ST1800 and ST500 For Sale
Used ST1800 (wide belt and stone) w/ ST500 edger Both units are in good-very good condition & well loved. They haven't been in service for 2 years now and were last running well. New relay for texturing controller has been purchased, but not yet installed. LOTS of extra belts! ST1800: - Stone i...
- Sun Jan 13, 2013 5:32 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Layup techniques to eliminate bubbles under clear top sheets
- Replies: 41
- Views: 25762
Western Cedar veneer with a paper backing. The paper is 10mil (0.01 inch) and the veneer is about the same (0.01 inch) for a total of 0.50mm. I was also thinking about the amount of time given to let the epoxy soak in... I'm going to try using a mix with a longer pot life so I can let is soak longer...
- Sun Jan 13, 2013 11:54 am
- Forum: Ski/Snowboard Design and Layup
- Topic: Layup techniques to eliminate bubbles under clear top sheets
- Replies: 41
- Views: 25762
'Fairly good' bonds don't cut it. Honestly didn't try to pick/peel it that hard... once a bit of it has lifted - as it would in a tip/tail cross hit situation - the rest peels back quite easily. I suppose I expect a discussion as to some solutions to the problem. I agree with you that the veneer is ...
- Sat Jan 12, 2013 10:23 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Layup techniques to eliminate bubbles under clear top sheets
- Replies: 41
- Views: 25762
Not too sure what you mean MM... How does it 'work fine' if the top sheet peels away from the veneer... seems to be a pretty good measure of bond if the 8210 can easily be pulled off the substrate. Cross tips and get a chip or lift in the 8210 and any curious monkey is going to pick at it regardless...
- Fri Jan 11, 2013 4:40 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Layup techniques to eliminate bubbles under clear top sheets
- Replies: 41
- Views: 25762
Re: Prepreg Solution?
RESULTS: Well, it works to a point, but ultimately is a fail. The paper backed veneer looks perfect and bonded well to the ski... the 8210 is bubble free and bonded well to the top of the veneer. Where it fails is that the 8210 is only bonded to the outter most, thinnest skin on the veneer. I think ...
- Fri Jan 11, 2013 12:47 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Layup techniques to eliminate bubbles under clear top sheets
- Replies: 41
- Views: 25762
Re: Prepreg Solution?
The first step went well. No problem seeing the bubbles and working them to the edge of the 8210 with the squeegy. The assembled veneer and 8210 has cured and can be formed to any shape, but is quite more stiff than either product on it's own. Next step is the actual mock-layup... more later. I am r...
- Fri Jan 11, 2013 10:28 am
- Forum: Ski/Snowboard Design and Layup
- Topic: Layup techniques to eliminate bubbles under clear top sheets
- Replies: 41
- Views: 25762
Prepreg Solution?
I am running a test that I will post an update on once I get some results... Using 8210 and laminating it to a paper backed wood veneer as a first step, basically creating a wood veneer prepreg to use in the layup process. Buttered the top side of the veneer and the bottom side of the 8210 and used ...
- Sat Sep 22, 2012 5:43 pm
- Forum: Yard Sale (non commercial)
- Topic: Edge Material For Sale
- Replies: 4
- Views: 3964
- Fri Sep 21, 2012 7:47 am
- Forum: Yard Sale (non commercial)
- Topic: Edge Material For Sale
- Replies: 4
- Views: 3964
Edge Material For Sale
Edge material... can send pictures of stamping profile.
84 inch long, 2mm profile, sandblasted and primed ready for layup.
152 pcs total.
Will sell entire lot for $684 ($4.50/pc).
Will also consider smaller quantities at $5.00/pc
Buyer pays shipping from Revelstoke, BC.
84 inch long, 2mm profile, sandblasted and primed ready for layup.
152 pcs total.
Will sell entire lot for $684 ($4.50/pc).
Will also consider smaller quantities at $5.00/pc
Buyer pays shipping from Revelstoke, BC.