Error
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
Error
planer crib.
Planer jig
Air Connection System
Hockey Stick Cat Track
Reinforcements (The Flat Bar is actually 5mm Square tubing, i didnt know that name at the time and the rod is 1 inch)
There is three of these truss supports
Poly Ethylene Cassette
Planer jig
Air Connection System
Hockey Stick Cat Track
Reinforcements (The Flat Bar is actually 5mm Square tubing, i didnt know that name at the time and the rod is 1 inch)
There is three of these truss supports
Poly Ethylene Cassette
Last edited by a.badner on Wed Feb 02, 2011 8:06 am, edited 12 times in total.
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
(it's funny that you typed more saying you were too lazy to correct the capital letters than just re-typing the letters in lower case)
Do you have a drawing or sketch of your press? What kind of beams are you using? I-beams, or something else?
We have to do emissions in washington state too. Who buys a cavalier in the first place! :p
Do you have a drawing or sketch of your press? What kind of beams are you using? I-beams, or something else?
We have to do emissions in washington state too. Who buys a cavalier in the first place! :p
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
Our press was originally just three 2x4 steel beams top and bottom (two laying down flat, the middle one vertical). At ~30psi the beams had deflected about 3/4"!a.badner wrote:
the frame feels sturdy extremely sturdy, but those 2x4 of steel, they seem kind of flimsy.
We had to add vertical supports to keep the loads a bit safer (we did three 2" square bars on either side of the press)
-
- Posts: 2337
- Joined: Tue Apr 07, 2009 3:26 pm
- Location: Western Mass, USA
- Contact:
You said the router bits got dull fast. If they are plain steel bits they will dull rather fast compared to higher grade bits. Not sure how you use your router but always do a rough cut w/ a jig saw. Then use the router. The bits aren't really made to go straight through material, especially if your router uses 1/4 inch bits. A 1/2 inch router can handle it but the bits will dull quicker that way.
As for the Cavalier.....We have emission inspection too in Mass. My daughter has a 1996 Volvo, a solid car (220,000+ miles) but the cost to fix emissions isn't worth the value of the car, IMO. After dumping $850 for emissions last year the check engine still came on so it failed again. So I found this "fix" by accident... Look for the ECU (Electronic Control Unit). It must have one somewhere or something similar. Unplug it. Then plug it back in. This made the check engine light turn off and pass emissions. Eventually the check engine light came back on. Mass used to use do emission tests from the tail pipe. Now they just plug into the cars computer.
As for the Cavalier.....We have emission inspection too in Mass. My daughter has a 1996 Volvo, a solid car (220,000+ miles) but the cost to fix emissions isn't worth the value of the car, IMO. After dumping $850 for emissions last year the check engine still came on so it failed again. So I found this "fix" by accident... Look for the ECU (Electronic Control Unit). It must have one somewhere or something similar. Unplug it. Then plug it back in. This made the check engine light turn off and pass emissions. Eventually the check engine light came back on. Mass used to use do emission tests from the tail pipe. Now they just plug into the cars computer.
Wait.....so you want me to tell Rich that you are angry at his/now your skis?a.badner wrote: If you are reading this Iggy, these are Rich Fahey's old skis... before he got on the on3p team. tell him that. Oh if you guys dont believe me, go to you tuba and look up rich fahey slamina. he used this ski in the segment.
I can do that, I suppose.
Maybe if you bought some ON3Ps instead your trekkers would still be alive