Second layup Complete
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
Second layup Complete
Just pulled a ski out of the press for my 13 year old daughter.
They look really good which makes the task of triming up some what daunting.
Does every body get gittery at this point?
I will be back at Mt Hotham at the end of the week.
My Wife intends to steal these boards for the trip because the rightfull owner is not coming up with us.
This is my fith post so hopefuly I should be able to add some build pics and some decent trip report pics.
They look really good which makes the task of triming up some what daunting.
Does every body get gittery at this point?
I will be back at Mt Hotham at the end of the week.
My Wife intends to steal these boards for the trip because the rightfull owner is not coming up with us.
This is my fith post so hopefuly I should be able to add some build pics and some decent trip report pics.
-
- Posts: 1148
- Joined: Tue Jan 08, 2008 6:02 am
- Location: NJ USA
- Contact:
water?
Yes 160L 2400W domestic hotwater service, 30W recirculating pump, 80m of good quality garden hose.
Threaded in cat track and base mold as 5 seperate elements.
Gets 75 deg.C peak. 2 deg.C per minute rate of change from pump turn on.
I wlll have to retro fit a stop tap as it tends to thermo syphon and prevent cool down.
Threaded in cat track and base mold as 5 seperate elements.
Gets 75 deg.C peak. 2 deg.C per minute rate of change from pump turn on.
I wlll have to retro fit a stop tap as it tends to thermo syphon and prevent cool down.
Falls, sidewall is UHMWPE sourced from Dotmar Australia. Black and neutral only. just bought half a sheet of each. Ski trimed up well, binding on, waxed and ready to rumble at Hotham on Friday morning.
Last edited by BlueRoof on Mon Aug 06, 2012 4:07 am, edited 1 time in total.
-
- Posts: 192
- Joined: Tue Mar 15, 2011 2:51 pm
Huck
Thanks Yes about four different species in shot. The core of the ski is a leftover board from the same pack of timber.
Falls
Huon River betweem Huonville and Frankiln a little further south and you fall of the edge. The ski is hand preped. Edges are rebated in to the core so it's very flat. I will give it one pass over a machine after a couple of days skiing.
Thanks Yes about four different species in shot. The core of the ski is a leftover board from the same pack of timber.
Falls
Huon River betweem Huonville and Frankiln a little further south and you fall of the edge. The ski is hand preped. Edges are rebated in to the core so it's very flat. I will give it one pass over a machine after a couple of days skiing.
-
- Posts: 192
- Joined: Tue Mar 15, 2011 2:51 pm
-
- Posts: 1354
- Joined: Mon Sep 17, 2007 7:37 pm
Re: water?
Nice looking skis.BlueRoof wrote:Yes 160L 2400W domestic hotwater service, 30W recirculating pump, 80m of good quality garden hose.
Threaded in cat track and base mold as 5 seperate elements.
Gets 75 deg.C peak. 2 deg.C per minute rate of change from pump turn on.
I wlll have to retro fit a stop tap as it tends to thermo syphon and prevent cool down.
If I am reading this correctly you are trying to cool the skis down in the press?
Don't.
Take them out and cool them on a flat surface with no pressure on them. You will get less variation in the flatness of the bases.
-
- Posts: 1148
- Joined: Tue Jan 08, 2008 6:02 am
- Location: NJ USA
- Contact:
- MontuckyMadman
- Posts: 2395
- Joined: Fri Jun 20, 2008 9:41 pm
dont cool the laminate under pressure.
Yes, pull hot and let cool at room temp.
You have very different coefficients of expansion in materials and cooling under pressure will lead to problems and non repeatable results. Trust me, been there, done that.
THanks again dbs.
Yes, pull hot and let cool at room temp.
You have very different coefficients of expansion in materials and cooling under pressure will lead to problems and non repeatable results. Trust me, been there, done that.
THanks again dbs.
sammer wrote: I'm still a tang on top guy.
Reply to Doughboyshredder
I did cool these in the press but not at pressure. The air temp. in my workshop that night was about 2 degrees C. That might be a bit harsh for room temp. cooling. Thanks for the tip though.