HB (Hansen Boards)
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
ANyway I made a couple of new cores so I can start on a new pair.
Firstly I cut a bunch of steel and drilled holes in it so I could use the bolts to pull the wood together.
Seems to make a nice even preasure, and works as a cheaper alternative to buying loads of huge G Clamps.
Firstly I cut a bunch of steel and drilled holes in it so I could use the bolts to pull the wood together.
Seems to make a nice even preasure, and works as a cheaper alternative to buying loads of huge G Clamps.
I am nobody. Nobody's perfect, so I must be perfect.
Wow, you really must have a lot of time.
If its only the veneer broken but the upper glass layer intact it shouldnt affect the rideability at all. So I would definitely give them a grind and test ride them. And I would do this before you press the next skis. Then you can adapt the new skis if needed.
If its only the veneer broken but the upper glass layer intact it shouldnt affect the rideability at all. So I would definitely give them a grind and test ride them. And I would do this before you press the next skis. Then you can adapt the new skis if needed.
No, I definitely do NOT have a lot of time.pmg wrote:Wow, you really must have a lot of time.
If its only the veneer broken but the upper glass layer intact it shouldnt affect the rideability at all. So I would definitely give them a grind and test ride them. And I would do this before you press the next skis. Then you can adapt the new skis if needed.
However I am going to Austria over Christmas hopefully to ski.. if there is any snow. And if I build something and present it to others, then I want it to be perfect. I'll be there nearly 2 weeks.
And to be honest I don't trust the plywood cores any more.
I am nobody. Nobody's perfect, so I must be perfect.
-
- Posts: 2337
- Joined: Tue Apr 07, 2009 3:26 pm
- Location: Western Mass, USA
- Contact:
The skis and snowboard look great! I like the HB design in the tip w/ the CF. Nice accent piece! Too bad the ski cracked. So is the ski toast? Did you lose the camber in the ski where the crack is? If so it's probably toast. Otherwise maybe you can salvage it, but if you do try bring another pairs of skis with you just in case :-).
Shit, I'm having problems. The cores I made looked beautiful. But after profiling they were 3.5 mm thick at the tips and realy stiff.
I tried sanding but it was too slow. So I put them back in the profile table, and stupidly took too much off so the cores were only about 1.4 mm in the front!! Much too thin.
Fooook.
I tried to compromise in the layup. I added a 160g/m² layer of carbon on the bottom and 200g/m² on the front of the ski.
Rest was 750g/m² Triaxial and a layer of 320g/m² Biax under binding.
We will see how it comes out. Bit I need to practice getting the correct thickness for my cores.
I tried sanding but it was too slow. So I put them back in the profile table, and stupidly took too much off so the cores were only about 1.4 mm in the front!! Much too thin.
Fooook.
I tried to compromise in the layup. I added a 160g/m² layer of carbon on the bottom and 200g/m² on the front of the ski.
Rest was 750g/m² Triaxial and a layer of 320g/m² Biax under binding.
We will see how it comes out. Bit I need to practice getting the correct thickness for my cores.
I am nobody. Nobody's perfect, so I must be perfect.
-
- Posts: 712
- Joined: Thu Sep 30, 2010 12:32 pm
- Location: USA
I think you're using router table, if not this doesn't apply.
Set up your table and use a piece of tip spacer to set the depth stop on your router. then put your core blank in and start cutting.
Leave the stop locked in this position until you are making something with thinner tip spacer, and you won't be able to cut too deep.
sam
Set up your table and use a piece of tip spacer to set the depth stop on your router. then put your core blank in and start cutting.
Leave the stop locked in this position until you are making something with thinner tip spacer, and you won't be able to cut too deep.
sam
You don't even have a legit signature, nothing to reveal who you are and what you do...
Best of luck to you. (uneva)
Best of luck to you. (uneva)
I was stupid and working under time preasure trying to get these finished this weekend. As was mentioned here recently. Don't work under time preassure.sammer wrote:I think you're using router table, if not this doesn't apply.
Set up your table and use a piece of tip spacer to set the depth stop on your router. then put your core blank in and start cutting.
Leave the stop locked in this position until you are making something with thinner tip spacer, and you won't be able to cut too deep.
sam
That is a good tip spacer tip ;-)
I am not using tip spacers, but I thought the other day I need to organize myself some 2.5 and 3mm material for this purpose.
I am nobody. Nobody's perfect, so I must be perfect.
Thanks skidesmond. I am pretty happy with them too.skidesmond wrote:The skis and snowboard look great! I like the HB design in the tip w/ the CF. Nice accent piece! Too bad the ski cracked. So is the ski toast? Did you lose the camber in the ski where the crack is? If so it's probably toast. Otherwise maybe you can salvage it, but if you do try bring another pairs of skis with you just in case :-).
I am not sure about the cracked ski, It is where the ski transitions from rocker into camber and definitely has a visible ridge on the bottom. I will probably try to ski on them anyway... However I have now built a new pair, and I will definitely have my Nordica Doberman's as a backup / hard snow ski.
I am nobody. Nobody's perfect, so I must be perfect.
See above..satch wrote:Looks pretty good.
What did you Change compared to the last one? What type and weight of fibers did you use?
I added a 160g/m² layer of carbon on the bottom and 200g/m² on the Top front of the ski.
Rest was 750g/m² Triaxial and a layer of 320g/m² Biax under binding.
the only other difference is I used an Ash core instead of the Birch Ply wood.
I am nobody. Nobody's perfect, so I must be perfect.
Thanks
The ash core will help A LOT. I would have added the carbon to the top Laminate. A thicker and stronger Laminate is not as prone to buckling.
People often make the mistake to put too much fibers into the botttom Laminate of a Sandwich. But as the fibers handle Tension better than pressure you Need to reinforce the pressure side (top of the ski).
The ash core will help A LOT. I would have added the carbon to the top Laminate. A thicker and stronger Laminate is not as prone to buckling.
People often make the mistake to put too much fibers into the botttom Laminate of a Sandwich. But as the fibers handle Tension better than pressure you Need to reinforce the pressure side (top of the ski).
OK, That makes sense.satch wrote:Thanks
The ash core will help A LOT. I would have added the carbon to the top Laminate. A thicker and stronger Laminate is not as prone to buckling.
People often make the mistake to put too much fibers into the botttom Laminate of a Sandwich. But as the fibers handle Tension better than pressure you Need to reinforce the pressure side (top of the ski).
I have Carbon on the top in the front 1/3 of the ski. So that will help there.
I am nobody. Nobody's perfect, so I must be perfect.