Ace skis first pair
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
- Head Monkey
- Posts: 310
- Joined: Sun Jul 17, 2005 4:53 pm
- Location: Carnation, WA
- Contact:
I clamp the base material down much like I do the core blanks: a few clamps along the length of each side. The machine starts cutting at the nose and makes a pass down one side. As it makes the turn around the tail and starts cutting the second side I start to stabilize the cut base by hand. As the cutter approaches the nose again I make sure to have one hand at the middle of the base and one close to the cutting head. I’ve found it’s easy to hold the base completely still this way. Alternatives might be double-sided tape, and of course a decent vacuum table, but since just holding it down has worked so well for me I’ve never been motivated enough to try something else.twizzstyle wrote:Hey Mike!
How are you holding your base material down while cutting with the straight flute bits?
Everything I know about snowboard building, almost: MonkeyWiki, a guide to snowboard construction
Free open source ski and snowboard CADCAM: MonkeyCAM, snoCAD-X
Free open source ski and snowboard CADCAM: MonkeyCAM, snoCAD-X
- Head Monkey
- Posts: 310
- Joined: Sun Jul 17, 2005 4:53 pm
- Location: Carnation, WA
- Contact:
Any straight flute bit will work. Personally I like to cut with a narrower cutter than a mortising bit tends to be, since a narrow bit makes it easier to avoid the clamps. I use the straight 1/4" bit you see here: http://www.happymonkeysnowboards.com/Mo ... outer_Bits Just don’t use a spiral cutter like the up-cuts you see there. Those are great for clearing wood chips, but they pull and tear at the thinner and more pliable base material and ruin it.ace skis wrote:will a Mortising Bit work?
Anyone got a part number and/or link for the drag knifes others are using? I’ve always wanted to try one…
Everything I know about snowboard building, almost: MonkeyWiki, a guide to snowboard construction
Free open source ski and snowboard CADCAM: MonkeyCAM, snoCAD-X
Free open source ski and snowboard CADCAM: MonkeyCAM, snoCAD-X
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
Brett (Brazen) grinds his own drag knives from carbide drill blanks. You just let the spindle freely rotate. All the drag knives I can come up with are for cutting sign vinyl, which would be way too delicate for cutting ptex. Brett seems to get great results with his home-ground drag knives, that's what I'm going to try.
Carbide blanks are only a few dollars on mcmaster.
Carbide blanks are only a few dollars on mcmaster.
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
Ha, glad you did it ok without my file - I still never emailed that to you (I have the file ready in the shop). You still want the DXF for the new looks? (looks like yours is for the old ones).
What's with the second set of holes? Cut in the wrong spot?
Funny story, on the last skis I did I used my CNC mill to cut the insert holes. Got everything lined up perfect, clamped down nice, starting cutting - and realized I had the core upside down. Funny when you have a CNC for ultimate precision, but you're cutting in the completely wrong spot
What's with the second set of holes? Cut in the wrong spot?
Funny story, on the last skis I did I used my CNC mill to cut the insert holes. Got everything lined up perfect, clamped down nice, starting cutting - and realized I had the core upside down. Funny when you have a CNC for ultimate precision, but you're cutting in the completely wrong spot
Ya haha I almost did that to but i caught it right in time thank good, what you end up doing just re drilling it on the other side? How I screwe up is i accidentally put the toe plate on the center line in stead of my boot mid point line. Also It be great if you could still send The template so i can use them in a few months on my next skis, but no rush.
I was was hopping those were the new looks but looks like im on the hunt for some old looks. Would you know a year by any chance? the link i used to mount them was http://www.tetongravity.com/forums/show ... -Templates
and on that site look_pivot_axial_paper_template_R2.pdf
Thanks for your help
Kenny
I was was hopping those were the new looks but looks like im on the hunt for some old looks. Would you know a year by any chance? the link i used to mount them was http://www.tetongravity.com/forums/show ... -Templates
and on that site look_pivot_axial_paper_template_R2.pdf
Thanks for your help
Kenny
Last edited by ace skis on Sun May 27, 2012 9:13 am, edited 1 time in total.
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
Luckily I caught it when it had only cut one hole, so I filled it with a mix of epoxy and sawdust, and after it was cured I machined it from the correct side and all was good.
I'm not entirely sure what years they were, but they're becoming hard to come by. I've used the old pivots for a long time now, but it is virtually impossible to find wide brakes for them, so I've had to use leashes. I finally decided this year it was time to get new bindings.
The toe pieces on the new Looks are identical to the old ones, and on the heals the forward two bolts are the same. Its just the aft-most two bolts that are moved forward a bit. I actually machined some aluminum adapter plates that allow me to mount the new Looks on inserts placed for the old looks The plate mounts to the ski, then the binding mounts to the plate. Works great.
I'm not entirely sure what years they were, but they're becoming hard to come by. I've used the old pivots for a long time now, but it is virtually impossible to find wide brakes for them, so I've had to use leashes. I finally decided this year it was time to get new bindings.
The toe pieces on the new Looks are identical to the old ones, and on the heals the forward two bolts are the same. Its just the aft-most two bolts that are moved forward a bit. I actually machined some aluminum adapter plates that allow me to mount the new Looks on inserts placed for the old looks The plate mounts to the ski, then the binding mounts to the plate. Works great.
Do you think i should fill the holes im not using? i was thinking i would just put inserts in all them and call it good also do you think a pair of 2005 look pivits would work? http://www.tetongravity.com/forums/show ... ide-brakes
-
- Posts: 1354
- Joined: Mon Sep 17, 2007 7:37 pm
IMO, you should always use reinforcements for inserts. I.E. Push the insert through a sheet of Kevlar or CF, or even glass, if you're not worried about weight. Also, they should be pushed in during layup, not before.
Only takes a little bit of extra time, and a little bit of extra money, and it eliminates any risk of your inserts being a weak spot.
Only takes a little bit of extra time, and a little bit of extra money, and it eliminates any risk of your inserts being a weak spot.
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
Yes those bindings will work.
Do waste the inserts putting them in the wrong holes. Mix up some kind of slurry with sawdust and epoxy (quick hobby epoxy is fine). When its cured sand it down flat and smooth on both sides. If you leave them open you'll get really bad divots in your topsheet and base. If you put inserts in... you're just wasting inserts.
I've never done any reinforcement with my inserts, but I've never put more than maybe 20 days on a pair of homemade skis, cause I keep making new ones.
Do waste the inserts putting them in the wrong holes. Mix up some kind of slurry with sawdust and epoxy (quick hobby epoxy is fine). When its cured sand it down flat and smooth on both sides. If you leave them open you'll get really bad divots in your topsheet and base. If you put inserts in... you're just wasting inserts.
I've never done any reinforcement with my inserts, but I've never put more than maybe 20 days on a pair of homemade skis, cause I keep making new ones.
Alright i already filled a creak in my ski core with glue and sawdust so i know the concept. This will be the last question i bug you with. I Profiled my skis down to 2mm at tip and they seem rely week almost like they would snap if you bent them is this just me being paranoid or are you sposted to be able to bend them with out worries.